See Our Reviews
x

2 Yelp Reviews

5.0


9 Google Reviews

5.0

Wine Cellar Refrigeration Solutions For the Trade Menu

Wine Cellar Refrigeration Systems – Vertical Rack Mount Cooling Units (VRM Series)

The Vertical Rack Mount (VRM series) wine cellar refrigeration systems are cooling units engineered to deliver refrigerated air to medium-high temperature spaces.

VRM Series
VRM evaporators mount vertically and have multiple panels to access direct or re-direct the supply and return vents. These can be placed between ceiling joists, in a soffit, or directly onto a wall. This is one of our most popular and versatile systems amongst our wine cellar cooling engineering community.

VRM evaporators are manufactured in standard capacities ranging from 2,600 to 6,600 BTU per hour and are used with R134a refrigerant.

The Vertical Rack Mount cooling series is a split system wine cellar refrigeration unit.

Series Options

  • Triple evaporator systems for larger applications.
  • Eco-friendly water-cooled condensing units are available.
  • Stainless steel cabinets for high corrosive environments.

Features

  • High-performance staggered coils with copper tubing mechanically expanded into aluminum fins
  • Rust-proof and insulated aluminum housing
  • Thermally protected permanently lubricated motor
  • The automatic expansion valve (standard) ensures constant coil temperature to promote “Humidity Balance”
  • Pump-down solenoid valve (standard) protects compressor in the event of leaks
  • Pre-installed valves eliminate additional wiring to the thermostat
  • Pressure tested by the manufacturer to ensure quality
  • Factory wired for simple field installation
  • ETL certified

Go to PDF Download & Full Specifications Page VRM-Series Wine Cellar Cooling Units

Mounting Diagrams

Question? Click here to get help with the Mounting Diagrams Vertical Rack Mount- VRM Series Custom Wine Room Cooling Units

Condensing Unit Wiring

Questions? Click here for assistance with the Condenser Unit Wiring Diagram Vertical Rack Mount- VRM Series Custom Wine Cellar Cooling Units

Fan Coil Wiring

Questions? Click here for assistance with the Fan Coil Unit Wiring Diagram Vertical Rack Mount- VRM Series Custom Wine Cellar Cooling Units

Field Wiring

L1115V Line Voltage

NNeutral

SVSolenoid Valve

FMFan Motor

TPTemperature Probe

Back of Controller Connections

10Temperature Probe

11Temperature Probe

4Neutral

5115V Line Voltage

2Jumper from 5

3Switch Leg to Fan Coil

C NOInternal normally open contact

VRM Cooling System – Typical Installation

  • Keep line sets as short as possible.
  • An excessive number of turns will cause refrigerant flow problems. This could cause early compressor failure. Suction line accumulators are recommended. Required if working lower than the normal 55-65° operating range from the wine cellar.
  • The drain line must always flow downhill to drain or pump.
  • The system is controlled by a pump-down control system. There is no control wiring between the thermostat and condensing unit.
  • The line connections at Fan Coil and Condensing Unit may not be the same as the required line sizes.
  • Standard line sets should be 50′ or less. Extended runs may require larger line sizes and 3oz oil must be added for every 10′ over 35′.

Question? Click here for assistance with the VRM Series Custom Wine Cellar Cooling UnitsInstallation Process

Question? Click here for assistance with the Vertical Rack Mount- VRM Series Custom Wine Cellar Cooling Units
Question? Click here for assistance with the Vertical Rack Mount- VRM Series Custom Wine Cellar Cooling Units

System Information

The Vertical Rack Mount (VRM) Systems are engineered to deliver refrigerated air to medium-high temperature spaces.

VRM evaporators mount vertically and have multiple panels to access direct or re-direct the supply and return vents. These can be placed between ceiling joists, in a soffit, or directly onto a wall. This is one of our most popular and versatile systems amongst our wine cellar cooling engineering community.

VRM evaporators are manufactured in standard capacities ranging from 2,600 to 6,600 BTU per hour and are used with R134a refrigerant.

VRM Series Wine Cellar Cooling Units - Rack Mount, great for Medium-High Temperature Wine Cellars, Vertical Rack, Soffit or Wall Mount

Mounting Diagrams

Question? Click here to get help with the Mounting Diagrams Vertical Rack Mount- VRM Series Custom Wine Room Cooling Units

Condensing Unit Wiring

Questions? Click here for assistance with the Condenser Unit Wiring Diagram Vertical Rack Mount- VRM Series Custom Wine Cellar Cooling Units

Fan Coil Wiring

Questions? Click here for assistance with the Fan Coil Unit Wiring Diagram Vertical Rack Mount- VRM Series Custom Wine Cellar Cooling Units

Field Wiring

L1115V Line Voltage

NNeutral

SVSolenoid Valve

FMFan Motor

TPTemperature Probe

Back of Controller Connections

10Temperature Probe

11Temperature Probe

4Neutral

5115V Line Voltage

2Jumper from 5

3Switch Leg to Fan Coil

C NOInternal normally open contact

VRM Cooling System – Typical Installation

  • Keep line sets as short as possible.
  • An excessive number of turns will cause refrigerant flow problems. This could cause early compressor failure. Suction line accumulators are recommended. Required if working lower than the normal 55-65° operating range from the wine cellar.
  • The drain line must always flow downhill to drain or pump.
  • The system is controlled by a pump-down control system. There is no control wiring between the thermostat and condensing unit.
  • The line connections at Fan Coil and Condensing Unit may not be the same as the required line sizes.
  • Standard line sets should be 50′ or less. Extended runs may require larger line sizes and 3oz oil must be added for every 10′ over 35′.
Question? Click here for assistance with the VRM Series Custom Wine Cellar Cooling UnitsInstallation Process
Question? Click here for assistance with the Vertical Rack Mount- VRM Series Custom Wine Cellar Cooling Units
Question? Click here for assistance with the Vertical Rack Mount- VRM Series Custom Wine Cellar Cooling Units

SYSTEM INFORMATION

The Vertical Rack Mount (VRM) Systems are engineered to deliver refrigerated air to medium-high temperature spaces.

VRM evaporators mount vertically and have multiple panels to access direct or re-direct the supply and return vents. These can be placed between ceiling joists, in a soffit, or directly onto a wall. This is one of our most popular and versatile systems amongst our wine cellar cooling engineering community.

VRM evaporators are manufactured in standard capacities ranging from 2,600 to 6,600 BTU per hour and are used with R134a refrigerant.

VRM Series Wine Cellar Cooling Units - Rack Mount, great for Medium-High Temperature Wine Cellars, Vertical Rack, Soffit or Wall Mount

Options

  • Triple evaporator systems for larger applications
  • Eco-friendly water-cooled condensing units available
  • Stainless steel cabinets for high corrosive environments

Features

  • High-performance staggered coils with copper tubing mechanically expanded into aluminum fins
  • Rust-proof and insulated aluminum housing
  • Thermally protected permanently lubricated motor
  • The automatic expansion valve (standard) ensures constant coil temperature to promote “Humidity Balance”
  • Pump-down solenoid valve (standard) protects compressor in the event of leaks
  • Pre-installed valves eliminate additional wiring to the thermostat
  • Pressure tested by the manufacturer to ensure quality
  • Factory wired for simple field installation
  • ETL certified

Mounting Diagrams

Question? Click here to get help with the Mounting Diagrams Vertical Rack Mount- VRM Series Custom Wine Room Cooling Units

Condensing Unit Wiring

Questions? Click here for assistance with the Condenser Unit Wiring Diagram Vertical Rack Mount- VRM Series Custom Wine Cellar Cooling Units

Fan Coil Wiring

Questions? Click here for assistance with the Fan Coil Unit Wiring Diagram Vertical Rack Mount- VRM Series Custom Wine Cellar Cooling Units

Field Wiring

L1115V Line Voltage

NNeutral

SVSolenoid Valve

FMFan Motor

TPTemperature Probe

Back of Controller Connections

10Temperature Probe

11Temperature Probe

4Neutral

5115V Line Voltage

2Jumper from 5

3Switch Leg to Fan Coil

C NOInternal normally open contact

VRM Cooling System Typical Installation

VRM Cooling System – Typical Installation

  • Keep line sets as short as possible.
  • An excessive number of turns will cause refrigerant flow problems. This could cause early compressor failure. Suction line accumulators are recommended. Required if working lower than the normal 55-65° operating range from the wine cellar.
  • The drain line must always flow downhill to drain or pump.
  • The system is controlled by a pump-down control system. There is no control wiring between the thermostat and condensing unit.
  • The line connections at Fan Coil and Condensing Unit may not be the same as the required line sizes.
  • Standard line sets should be 50′ or less. Extended runs may require larger line sizes and 3oz oil must be added for every 10′ over 35′.
Question? Click here for assistance with the VRM Series Custom Wine Cellar Cooling UnitsInstallation Process
Question? Click here for assistance with the Vertical Rack Mount- VRM Series Custom Wine Cellar Cooling Units
Question? Click here for assistance with the Vertical Rack Mount- VRM Series Custom Wine Cellar Cooling Units

GO HERE TO SEE other wine cellar refrigeration units by US Cellar Systems.

Call +1 (562) 513-3017 & ask for Systems Design

US Cellar Systems creates cooling systems for every size and style of refrigerated wine storage. We have multiple product lines available and can work with you to select and customize the most effective cooling unit for your projects. We are proud to work with builders, contractors, designers, architects, and other custom wine cellar construction experts. Call us today in California at (562) 513-3017 or in Oregon at (503) 928-8778!